3D Printer and CNC parts
LCDs and Displays
Shields and Carriers
Azteeg X3 Full Featured 3D Printer Controller v2.0
Azteeg X3 3DP Reprap Controller w/ ATMEGA2560
Quantity in Stock:29
Usually Ships in 1 to 2 Business Days
Vertical Male Header [Soldered]
Screw Terminals [Terminal Blocks] Soldered [Add $3.00]
Vertical male header with wire harness. [Add $11.00]
Micro SD card:
4GB Micro SD card [Add $6.00]
V2.0 Cover Shield
v2.0 Cover Shield w/ 2 thermocouple inputs [Add $7.00]
4pcs SD8825 w/ Heatsink [Add $46.00]
5pcs SD8825 w/ Heatsink [Add $57.50]
Helios 200 Heat Bed 12V [Add $38.00]
3 Mechanical Endstops [Add $4.50]
6 mechanical Endstops [Add $9.00]
2pcs Epcos 100k Thermistors [Add $7.00]
3pcs Epcos 100k Thermistors [Add $10.00]
Detailed Options information
Changes on version 2.0 of the Azteeg X3 Controller.
Digital pot control for stepper drivers ( on SD8825 drivers only)
2A internal +5V supply capacity
More robust SD card slot with push-in push-out mechanism
4 Layer, 2 Oz copper PCB ( including internal layers)
2 High capacity servo control on top cover
Decay mode setting solder jumpers for SD8825 stepper drivers
Improved layout for better current handling, heat dissipation.and minimize noise.
Changed to through hole USB mini B connector
Plus other minor changes to improve performance and stability.
The Azteeg X3 is a full featured, easy to use 3D printer Electronics powered by the reliable and powerful Atmel ATMEGA2560 micro controller.The X3 is designed with excellent high current capability to run most 3D printer configurations including those with dual extruders and large, power hungry heated beds.. Will work with Prusa Mendel, Mendel Max, Ordbot, Printrbot and most 3D printers.
We've combined the RAMPS and the Arduino Mega into one sleek package, added lots of cool stuff, beefed up power handling and made the Azteeg X3 pin to pin compatible with the popular RAMPS controller. This means you can use it right out of the box. Compatible with all mainstream reprap 3D printer firmwares including SPRINTER, MARLIN, REPETIER and others.
The X3 has a removable top shield to physically protect its parts which also doubles as an expansion board. Printing via micro SD card is now easier with the built-in microSD slot and also has built in buzzer.
For more information on installation visit the
Azteeg X3 reprap.org wiki page
Check the "Detailed Options" Tab for descriptions of all the available options.
Atmel ATmega 2560 with FT231x FTDI USB chip
Compatible with Sprinter, Marlin, Repetier, others.
Total of 8 stepper motor control including 3 external for high current stepper drivers(v1.1 shield)
Mosfet control for 4 Hotends and 1 hotbed using latest shield
4 low power PWM Mosfet driven outputs for LEDs and Fans
2 High capacity servo outputs on cover
6 end stops and 3 thermistor inputs
Wide input high efficiency switching Power supply (5v @ 2000ma max on V2.0)
microSD card socket built-in
On board buzzer
Fused and Zener protected +5v Vcc line.
Ultra Low RDSon, High power Mosfets for minimal heat buildup
Input power selector for micro controller [USB or internal regulator]
Secondary power input for stepper motors.
High current capacity connectors and PCB traces.
Made with 4 layer 2 oz. copper (per layer)
Shield to protect electronics and act as expansion board
i2C, +5, GND, SPI and Analog/Digital pins on the expansion ports
Fast acting blade fuse
Screw terminal or crimp type connector options
Lots of LEDs, Rx/TX serial, PWR, hot end and hot bed.
What's in the box:
Azteeg X3 3DP controller board with Arduino Bootloader and Test Firmware
X3 V2.0 Wiring Diagram - PDF
X3 V1.1 Wiring Diagram - PDF
X3 V1.0 Wiring Diagram - PDF
RepRap Wiki page
SD8825 User Guide
Helios Heated Bed user guide
Azteeg X3 Test Code
FTDI USB Drivers
- (Made with Diptrace PCB software)
Azteeg X3 in action
Terminal Blocks comes soldered with orders starting June 18th unless otherwise requested. Push-fit connectors, vertical or right angle will come unsoldered to the board unless requested to be soldered.
Vertical Crimp Style Header with wire harness.
This includes polarized vertical male headers, mating housing connector and crimp pins.
Right Angle Crimp Style Header with wire harness.
This includes polarized right angle male headers, mating housing connector and crimp pins.
Terminal Blocks or screw terminals.
These are standard terminal blocks. No crimping needed. Easy to connect wires but needs more work disconnecting if board is replaced or moved to a different printer.
With wire harness (wire is crimped).
This option is the same as the first two but has the wires crimped and ready to go. Wire size for motors is AWG22 and 26 for the stops and therminstors. 11 wire assemblies in all and comes in 24" wire length. This may be the easiest option for most users.
Version 1.1 Cover shield.
The expansion shield has been upgraded and now has the following features
2 additional power mosfet switches for Hotends for a total capability of 4 for the X3.
2 additional Thermistor inputs
2 additional connections for external stepper drivers
Central stepper fault detect ( for use with the new SD8825 stepper drivers only)
1 additional expansion header (usable only with X3 v1.1)
Stepper Drivers based on the robust Ti DRV8825
Comes with relatively large 11mm x 10mm x 5mm heat sink. Other heat sink sizes available.
2.5 amp drive limit with overload and thermal protections.
Breakout pins for Decay, Fault and external Vref for software set current limit
1, 1/2, 1/4, 1/16 and 1/32 microsteps
Excellent heat dissipation. Heat tab on top PCB layer as recommended by the manufacturer. Will accept larger heatsinks
Pin compatible and with pololu style drivers. Drop in replacement, no mods needed.
Lead free RoHS PCB
All parts are at the bottom except for trimmer.
Headers comes soldered
Heated Bed Platform:
(Glass top Required)
Helios Heated Bed
PCB Heated bed made from TG170 High temp material. RoHS ENIG Gold.
0.125 inch THICK
Screw Mounting holes for wires - No more broken solder joints. Yes!
Countersunk mounting holes for totally flat printing surface. MKII compatible mounting pattern.
Top mounted heating traces for direct contact with glass.
Thermistor trace from center to edge. No need to tape wires.
Four extra countersunk holes for user made custom glass mounting clips.
Comes with Stainless steel mounting hardware.
Will fit on Prusa, MendelMax, Ordbots, and others that use the MKII PCB mounting pattern
Azteeg X3 Pro
azteeg X5 mini reprap 3d printer controller
azteeg X1 reprap 3d printer controller
Azteeg G1-328P CNC Controller w/ 3AX Driver module
| Total Reviews:
Write a review »
1 of 1 people found the following review helpful:
Bootloader is corrupt
September 2, 2014
Reviewer: Anonymous Person from Irvine, CA United States
Bootloader is corrupt, and avrdude does not verify the firmware that was uploaded. Contacted support, but have been waiting 5 days for a response.
Was this review helpful to you?
Join Our Mailing List
Terms and Conditions